Perancangan dan Implementasi Sistem Elektrik serta Otomasi pada Mesin Pencetak Briket Berbasis Cangkang Kelapa Sawit dengan Kapasitas 40 Kg/jam

Abstract

Palm oil is a leading agricultural commodity in Indonesia, producing CPO and PKO from the processing of fresh fruit bunches. As palm oil production increases, the volume of solid waste also increases. Solid waste from this industry, such as empty fruit bunches, shells, and fibers, contains high levels of organic matter that can pollute the environment if not managed properly. Briquettes are an alternative energy source that can be produced from this waste. This research aims to utilize palm oil shell waste into high-quality briquettes by developing an efficient charcoal briquette-making machine. The focus of the research is on developing a semi-automatic machine using a pneumatic system and a three-phase motor. Theoretical screw speed was approximately 44 rpm, while direct measurement on the machine showed 43 rpm. Furthermore, the theoretical results obtained a motor power requirement of 667.3 Watts.

Keywords

Kelapa sawit, Limbah Briket, Mesin pencetak briket, Mesin semi otomatis

Full Text:

XML

References

Arifandy, “Potensi Limbah Padat Kelapa Sawit Sebagai Sumber Energi Terbarukan Dalam Implementasi Indonesian Sustainability Palm Oil PKS Sungai Galuh,” Jurnal Sains, Teknologi dan Industri, vol. 19, no. 1, pp. 116–122, 2021.

Asiva Noor Rachmayani, Direktori Perusahaan Perkebunan Kelapa Sawit. Badan Pusat Statistik, 2020.

L. Fitria, R. Mulyawan, I. Ishak, S. Sulhatun, M. Meriatna, and I. Kamar, “Pemanfaatan Limbah Cangkang Kelapa Sawit Sebagai Pembuatan Briket Dengan Perekat Tepung Singkong Sebagai Bahan Bakar Alternatif,” Chemical Engineering Journal Storage (CEJS), vol. 2, no. 5, p. 138, 2023, doi: 10.29103/cejs.v2i5.9274.

A. N. Chansa et al., “Upaya Pemanfaatan Limbah Kelapa Sawit,” Jurnal Sains Student Research, vol. 2, no. 2, pp. 148–153, 2024.

E. Kurniawan, A. Muarif, and K. A. Siregar, “Pemanfaatan Sekam Padi dan Cangkang Sawit Sebagai Bahan Baku Briket Arang dengan Mengggunakan Perekat Tepung Kanji,” Seminar Nasional Pengabdian Masyarakat LPPM UMJ, pp. 1–9, 2022.

D. Arisandi, F. Novianti, and R. M. F. Krisnandhy, “Rancang Bangun Mesin Pencetak Briket Arang,” Politeknik Manufaktur Negeri Bangka Belitung, vol. 1, no. 1, pp. 1–87, 2022.

A. Ansar, D. A. Setiawati, M. Murad, and B. S. Muliani, “Karakteristik Fisik Briket Tempurung Kelapa Menggunakan Perekat Tepung Tapioka,” Jurnal Agritechno, vol. 13, no. 1, pp. 1–7, 2020, doi: 10.20956/at.v13i1.227.

Y. R. Kusuma, A. P. Cahyani, E. Aprilianto, and B. Prazidno, “Prosiding Seminar Nasional Prosiding Seminar Nasional Prosiding Seminar Nasional,” Proseding Seminar Nasional Politeknik Pembangunan Pertanian Yogyakarta Magelang, pp. 5–6, 2023.

E. Adril, Menhendry, D. Budiman, M. R. Araliz, and A. P. Yeni, “Rancang Bangun Mesin Pencetak dan Pemotong Briket dengan Sistem Elektro Pneumatik untuk UMKM,” Jurnal Teknik Mesin Politeknik Negeri Padang, vol. 17, no. 1, pp. 70–75, 2024.

P. Program, S. Teknik, E. Universitas, and I. Sultan, “Comparison Analysis of Start of 3 Phase Induction Motor Soft Starter Igbt Based on Sine-Triangle and Sine-Sawtooth Pwm Using Matlab Simulink Final Project,” 2022.

http://dx.doi.org/10.28989/angkasa.v17i2.3325

Article Metrics

Abstract view: 0 times
Download     : 0   times

This work is licensed under a Creative Commons Attribution 4.0 International License.

Refbacks

• There are currently no refbacks.