Design And Analysis of CFD Geometry Configuration Canted Winglet Toward Aerodynamic Characteristic on Wing Profil of The UAV LSU-05

Abstract

The wing is part of an aircraft or UAV which has a function as a major component of producing lift, therefore if a problem occurs such as a vortex at the end of the wing it will affect its performance capability. This study aims to determine the condition of the airflow, the value of induced drag, and the selection of the design of the wingtip devices on the wing profile of the UAV LSU-05. The method used is numerical or computational methods with CFD-based software to predict the aerodynamic characteristics and phenomenon of airflow around the wing with wingtip devices and without it. The model used in this study is a half-wing LSU-05 with NACA 4415 made with CATIA V5R20 software and the simulation uses ANSYS CFX 17.1. Based on the previous simulation results, it was found that the application of the canted winglet geometry to the wing profile of the UAV LSU-05 affects the coefficient lift (C_L)/coefficient drag (C_D) value and induced drag. Whereas the coefficient lift (C_L)/coefficient drag (C_D) value before using the canted winglet was 18.904 after application, increased to 21.616, this causes the induced drag value to change inversely with the coefficient lift (C_L)/coefficient drag (C_D) value where the value before the application was 30.4181 N to 29.0566 N.

Keywords: Canted Winglet, CFD, Wing

Full Text:

PDF

References

A. Romadhon, B, and D. Herdiana, “Analisis CFD Karakteristik Aerodinamika Pada Sayap Pesawat LSU-05 Dengan Penambahan Vortex Generator”, Jurnal Teknologi Dirgantara. Vol. 15 No. :45 -58, 2017.

P. Panagiotou, P. Kaparos, K. Yakinthos, “Winglet Design and Optimization for a Male UAV Using CFD”, Aerospace Science and Technology, technology 39: 190 – 205, 2014.

D. P. Raymer, “Aircraft Design: A Conceptual Approach”, 1992.

CAE Oxford Aviation Academy, “Principles of Flight ATPL Ground Training”, 2014.

McCormick dkk, “Aerodynamics, Aeronautics, and Flight Mechanics”, 1979.

A. I. Gölcük dkk, “Winglet Design and Analysis for Low-Altitude Solar Powered UAV”, Int. J. Sustainable Aviation, Vol. 3, No. 1, 2017.

K. A. Al Sidairi dan G. R. Rameshkumar, “Desain of Winglet device for aircraft”, International Journal of Multidisciplinary Sciences and Engineering, Vol. 7, No. 1, 2016.

Da Lyu, Baowei Song, Guang Pan, Zhiming Yuan, and Jian Li, “Winglet effect on hydrodynamic performance and trajectory of a blended-wing-body underwater glider”, Ocean Engineering 188 (2019) 106303.

I. Hanif, G. Jatisukamto, A. A. An Nafi, “Pengaruh Sudut Tekuk (Cant) Winglet Menggunakan Airfoil Naca 2215 Pada Aerodinamika Sayap Pesawat”, Jurnal ROTOR, Edisi Khusus No. 3, Desember 2017.

M. Barrios dan P. Herman, “Reducing Drag by Modifying the Winglet Design”, The Philippine Physics Society Physics Fair, Cebu. ResearchGate. 2017.

S. Rajendran, “Design of Parametric Winglets and Wing tip devices – A Conceptual Design Approach”, 2012.

http://dx.doi.org/10.28989/vortex.v2i1.931

Article Metrics

Abstract view: 506 times
Download     : 473   times

This work is licensed under a Creative Commons Attribution 4.0 International License.

Refbacks

• There are currently no refbacks.