Identifikasi kecacatan produk menggunakan Lean Six Sigma melalui pendekatan konsep DMAIC

Muh Yazid Gandi, Asep Erik Nugraha, Apid Hapid Maksum, Billy Nugraha

Submitted : 2022-03-17, Published : 2022-11-01.

Abstract

Lean Six Sigma has been known as part of a method for identifying the defects of a product. One approach is the DMAIC Concept, namely Define, Measure, Analyze, Improve and Control. It is to be oriented that it will be known the average product is defective and needs to be done the act of improvement. So the purpose of this study is to find out the type of product defects in the form of dolls, carpets and mattresses. The scientific was result in one just for Doll Industries locating at North Cikampek Village, Karawang Regency. Result from scientific, have 5 (five) categories of product defects in the form of: untidy stitching, uneven doll stuffing, wrinkle dolls, materials that are not environmentally friendly and colors are not appropriate. At the Define stage, problem identification, goal determination, process objectives and improvements are carried out. In the Measure stage, crtitical to quality (CTQ) measurements are taken. At the Analyze stage, a cause-and-effect analysis is performed. In the Improvement stage, the analysis of 5W+1H is carried out. At the Control stage, continuous improvement control is carried out.

Keywords

Kecacatan produk; Lean six sigma; DMAIC

References

B. Nugraha, Pengembangan Sumber Daya Manusia: Deskripsi Teoretis tentang Kinerja Pegawai, Penilaian Kinerja Pegawai dan Pemeliharaan SDM, Banyumas: CV. Pena Persada, 2021. Doi : 10.31237/osf.io/wrg85

E. Lena and L. Anatan, Managemant Operasi - Konsep Dan Aplikasi, Bandung: PT Refika Aditama, 2008.

S. Prawirosentono, Filosofi Baru Tentang Mutu Terpadu Edisi 2, Jakarta: Bumi Aksara, 2007.

I. Rinjani, W. Wahyudin and B. Nugraha, "Analisis Pengendalian Kualitas Produk Cacat pada Lensa Tipe X Menggunakan Lean Six Sigma dengan Konsep DMAIC," UNISTEK: Jurnal Pendidikan dan Aplikasi Industri, vol. VIII, no. 1, pp. 18-29, 2021. Doi : 10.33592/unistek.v8i1.878

E. N. A. Satya, W. Wahyudin, B. Nugraha and R. Ramadan, "Perbaikan Kualitas Produk Batu Bata Merah dengan Metode Six Sigma-DMAIC (Studi Kasus CV. Ghatan Fatahillah Karawang)," UNISTEK: Jurnal Pendidikan dan Aplikasi Industri, vol. VIII, no. 1, pp. 6-10, 2021. Doi : 10.33592/unistek.v8i1.1073

W. Wahyani, A. Chobir and D. D. Rahmanto, "Penerapan Metode Six Sigma dengan Konsep DMAIC sebagai Alat Pengendali Kualitas," in Prosiding Seminar Nasional Manajemen Teknologi XII, Yogyakarta, 2010.

F. Ahmad, "Six Sigma DMAIC sebagai Metode Pengendalian Kualitas Produk Kursi pada UKM," JISI : Jurnal Integrasi Sistem Industri, vol. VI, no. 1, pp. 11-17, 2019. Doi : 10.31315/opsi.v11i1.2241

J. Susetyo and C. Hartanto, "Aplikasi Six Sigma DMAIC dan Kaizen sebagai Metode Pengendalian dan Perbaikan Kualitas Produk," Jurnal Teknologi, vol. I, no. 1, pp. 53-61, 2011.

Y. F. Suci, Y. N. Nasution and N. A. Rizki, "Penggunaan Metode Seven New Quality Tools dan Metode DMAIC Six Sigma pada Penerapan Pengendalian Kualitas Produk (Studi Kasus: Roti Durian Panglima Produksi)," Jurnal Eksponensial, vol. I, no. 1, pp. 27-36, 2017.

H. T. Tan, "Metode DMAIC sebagai Solusi Pengenalian Kualitas Produksi Sepatu Tambang: Studi Kasus PT Jaya-Bekasi," ComTech, vol. III, no. 1, pp. 509-523, 2012. Doi : 10.21512/comtech.v3i1.2450

S. Reksohadiprodjo and I. Gitosudarmo, Manajemen Produksi Edisi 4, Yogyakarta: BPFE UGM, 2000.

S. Prawirosentono, Manajemen Operasi Analisis dan Studi Kasus, Jakarta: Bumi Aksara, 2001.

L. Wilson, How to Implement Lean Manufacturing, New York: McGraw-Hill, 2010.

V. Gaspersz, Lean Six Sigma for manufacturing and service industries, Jakarta: PT. Gramedia Pustaka Utama, 2007.

N. C. Pande, The Six Sigma Way, Yogyakarta: Penerbit ANDI, 2003.

P. Jirasukprasert, G.-R. J. Arturo, V. Kumar and K. M. Lim, "A Six Sigma and DMAIC Application for the Reduction of Defects in a Rubber Gloves Manufacturing Process," International Journal of Lean Six Sigma, vol. V, no. 1, pp. 2-21, 2014. Doi : 10.1108/IJLSS-03-2013-0020

M. N. Nasution, Manajemen Mutu Terpadu (Total Quality Management), Jakarta: Ghalia Indonesia, 2005.

F. Tjiptono and A. Diana, Definisi Kualitas, Yogyakarta: Bumi Aksara, 2001.

V. Gaspersz, Manajemen Produktivitas Total, Jakarta: PT. Gramedia Pustaka Utama, 2000.

S. D. Tanjong, "Implementasi Pengendalian Kualitas dengan Metode Statistik pada Pabrik Spareparts CV. Victory Metallurgy Sidoarjo," Calptra : Jurnal Ilmiah Mahasiswa Universitas Surabaya, vol. I, no. 1, pp. 1-10, 2012.

E. R. Cahyanti, M. Choiri and R. Yuniarti, "Pengurangan Waste pada Proses Produksi Botol X Menggunakan Metode Lean Sigma," Jurnal Rekayasa dan Manajemen Sistem Industri, vol. VIII, no. 2, pp. 37-46, 2013.

D. Sinta, F. N. Azizah and B. Nugraha, "Analisis Pengaruh Refiner Time terhadap Quality Tissue (Studi Kasus di PT. Pindo Deli Pulp and Paper Mills 2)," Angkasa : Jurnal Ilmiah Bidang Teknologi, vol. XIII, no. 1, 27-36, 2021. Doi : 10.28989/angkasa.v13i1.916

Article Metrics

Abstract view: 141 times

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Refbacks

  • There are currently no refbacks.